US SHIP AUDI C6 Q7 A6 Steering Column Module J518 ELV Emulator with VVDI Dedicated Programming Cable Fit for R270 CGDI CG100 CG100X XHORSE VVDI Prog
TOOLS in EU TAX FREE
TOOLS in US TAX FREE
We are here to provide you with a Better Price:
Email: Sales@OBDII365.com
Whatsapp:+86 18259252285
Business Whatsapp: +44 7418605489
Product Description
- Used with R270 CGDI CG100 XHORSE VVDI Prog Programmer.
- Applied to repair the AUDI sixth Gen A6 Q7 Audi C6 steering column lock J518 ELV module failure replacement emulator.
Introduction:
Applied to repair the AUDI sixth Gen A6 Q7 Audi C6 steering column lock J518 ELV module failure replacement emulator.
Highlights
- Can be used with R270, CGDI CG100 ,CGDI CG100X, XHORSE VVDI Prog Programmer
- Universal solution, three types of MCU all can be replaced by this emulator, (replace MCU Mask: 1L59W, 3L40K, 0L01Y directly);
- Stable and durable, with No Vulnerable components such as relays, micro switches, and motors on it.
- Easy for replacing, write in the dump form the original J518 Module with the VVDI PROG dedicated line directly, No need for solder wire.
The emulator without lock or on lock function, if need the same function as the original J518 Module, please buy the J518 Replacement
The VVDI PROG dedicated programming cable connector here is only for programming the emulator board, not for the original J518 PCB board.
so if you have a car that needs to replace the J518 module with this emulator, you need to read out the data in the MCU by soldering wire or other methods, then write the data into the emulator MCU via this Dedicated cable connector.
How to use:
1. Read out the EEPROM data from the original J518 module of your car (the emulator was already with flash data)
2. Write the EEPROM data you got in Step 1 into the emulator (if the original J518 MCU mask is 0L01Y, write the EEPROM data you got from step1 into the emulator directly;
or if the MCU mask of the original J518 is 1L59W/3L40K, you need to send EEPROM data to an expert to transfer EEPROM data when you write into the emulator directly. We don't provide the service)
SUGGESTION:
We are here for you:
Skype: OBDII365.com
Email: Sales@OBDII365.com
Whatsapp : +86 18259252285
Business Whatsapp: +44 7418605489
Tech Support
Here is the AUDI C6 Q7 A6 Steering Module Repair J518 ELV Emulator 256,128 simulate board operation instruction.
Do backup original eeprom data in case of lost data before operation. Read and save data.
If your car ELV has 9S12DG 128 CPU, the operation steps are as follows.
9S12DG 128 CPU operation steps:
1.Read and backup original EEPROM data.
2. Paste EEPROM data to EEPROM 2K-4K folder.
Double-click EEPROM Converter-x86 application.
You will see the original 2K file converted to 4K.
You will see the file is 4K
Only double-click this program once. Do not repeat.
If 2k file does not contvert to 4K, right click and run EEPROM Converter-x86 as asministor
3. Connect flashing wire and write the converted 4k eeprom file.
For simulator chip 256, select J518(2010)(0L01Y) in vvdi prog software
Each ELV emulator board contains both eeprom data and FLSAH data, so usually you just need to write Eeprom data. If not, you can write original eeprom data and the FLASH data in the emulator.
If car ELV has 9S12DG 256 CPU, the operation steps are as follows.
Read out and save the original eeprom data, and write it directly to the simulator.
without horn wiring connection
red (thick) =VCC
black (thick) =GND
yellow =RST
purple =BKGD
green =XCLKS
White =CLK
black (fine) =GND-C
with horn wiring connection
follow same wiring diagram as without horn above
With the VVDI Prog Dedicated Programming Cable, you can connect ELV emulator without soldering, directly insert into the 20pin port.
Attention:
Better put J518 ELV emulator to car after write data.
In the test platform test, better check the wiring of 20Pin port. Some test platforms will conflict with the 20pin port which leads to the chip being corrupted.
Error wiring: 10 (red) should be in position 20 (blue), as shown in the figure.
