How to Configure WiFi and USB for Original JLR DoIP VCI


Part 1: How to Configure WiFi for Original JLR DoIP VCI /setup wireless connection?


Original Jaguar Land Rover diagnostic tool JLR DoIP VCI supports both USB and WiFi connection. Here’s the guide to configure the LAN setting.

wifi-jlr-doip-vci

Procedure:

Connect JLR DoIP VCI W-F interface with vehicle

Connect the other end of VCI with laptop via USB cable

jlr-doip-vci-sdd-1

Open VCI Manager (JLR), press Connect

jlr-doip-vci-sdd-2

Choose Network Setup tab->Wired Etherent

jlr-doip-vci-sdd-3
Tick Enable Wired Etherent Interface

jlr-doip-vci-sdd-4

Press Apply button and Yes

jlr-doip-vci-sdd-5

Then disconnect USB connection

Close VCI Manager

 

Open VCI Manager again

Press Connect

Go to Network Setup->Wired Etherent

Press Set Factory Default

jlr-doip-vci-sdd-6

Press OK if system prompts you are about to reset the VCI communication settings to a factory default state.

jlr-doip-vci-sdd-7

Enable network connection

Press Set Factory Default again

jlr-doip-vci-sdd-8

In Wireless (802.11), choose Obtain an IP address automatically, then press Access Point

jlr-doip-vci-sdd-9

Choose Wireless resource which is the same as the your network
Press Configure

jlr-doip-vci-sdd-10

Enter wireless security password (encryption key)

Press Next

jlr-doip-vci-sdd-11

JLR VCI is configured to connect to your network

Disconnect and then Connect VCI

jlr-doip-vci-sdd-12

It shows WiFi connection is done

 

Open JLR SDD software on desktop

jlr-doip-vci-sdd-13

Press Connect

jlr-doip-vci-sdd-14

Now you can run SDD software for diagnosis

jlr-doip-vci-sdd-15

jlr-doip-vci-sdd-16

Part 2: How to connect JLR DoIP VCI via USB 

To setup USB connection, you need to download Bosch driver for VCI first:

https://mega.nz/#!aqwnhbQS!KS7QhERmZ4cCcZfvT2iXkdYN6ynz9vDQ3DmPQRGm0TU

 

Open Bosch_Driver folder

setup-jlr-doip-vci-usb-1
Open MTS6533_Setup

setup-jlr-doip-vci-usb-2
Install Bosch VCI Software (JLR)
Press Next
Press Next
Press Install
Finish installing Bosch VCI software

setup-jlr-doip-vci-usb-3
USB Configuration in progress. Don’t disconnect JLR VCI from PC until a message indicates that the configuration process has completed.

setup-jlr-doip-vci-usb-4

Open Device Manager to check the Bosch JLR DoIP VCI adapter is well connected

setup-jlr-doip-vci-usb-5

Open VCI Manager on desktop to make sure the Manager detect JLR VCI which indicates interface is well connected

setup-jlr-doip-vci-usb-14

Right click JLR SDD software on desktop->Find File location C:/Program Files/JLR/SDD/Runtime

setup-jlr-doip-vci-usb-6
Open the GatewayManager with Notepad
Find “Device5 = JLR-DOIP” and change value to “ Device5 = JLR-DOIP”

setup-jlr-doip-vci-usb-7Find Go to C:/Program Files/JLR/IDS/Runtime

setup-jlr-doip-vci-usb-9
Open the GatewayManager with Notepad
Find “Device5 = JLR-DOIP” and change value to “ Device5 = JLR-DOIP”

setup-jlr-doip-vci-usb-10

Setup completed.

Now you can run JLR SDD and Pathfinder software

setup-jlr-doip-vci-usb-11