V2021.03 MB SD Connect Compact C4 Star Diagnosis Supports Cars and Trucks
*MB SD C4 (SP100-D with Serial Number 101044) cannot use 2020.03 or above xentry software. Use 2019.12 or older Xentry. Otherwise device will be locked.
This SD Connect C4 Can Not work on IBM T30 Laptop
1. Internal Dell D630 hard drive/HDD works on Dell D630 laptop ONLY;
2. External HDD have no laptop limitation, but make sure your laptop meet the requirement: CPU 2.0, RAM 2GB. External HDD does not support WiFi
How to activate MB SD Connect Compact 4 Xentry & DAS software
MB SD Connect C4 Supported Vehicles List:
MB SDConnect C4 Function:
1. New MB SD Connect Compact 4 Star Diagnosis not only works with K line diagnose and CAN BUS,but also for UDS diagnose protocol.Old MB STAR C4 can not support these 2 functions,because old MB STAR C4 main board does not have UDS chip.
2. New MB SD Connect Compact 4 Star Diagnosis supports wifi diagnose.
3. Multiplexer supports Lan cable connection.
4. Connector adopts Military quick swap technology, so it can support 10,000 times pull plug, more stable.
5. All core accosseries adopt original new packing chip, 24hours test, product quality is guaranteeed .
Bz ORIGINAL ANTI-THEFT
KEYZESS GO SYSTEM
Product software includes: (Version: 2019.09)
Star Finder 2008 & 2016
Support languages: English, Croatian, Czech, Danish, Dutch, Finish, French, German, Greek, Hungarian, Italian, Japanese, Korean, Polish, Portuguese, Romanian, Russian; Spanish, Swedish, Turkish, Chinese.
How to set MB SD C4 WIFI?
Disconnect the local area connection, then connect the sdconnect 4 with the car and start the car, finally connect to the wireless connections, please follow the next instructions to set:
1.Click Configuration-MUX-Register/configure, under the "General information", select name "04" and then tick off "Wlan parameters, road"
2.Set the following parameters: IP address: 192.168.2.200, Network screen: 255.255.255.0, Encryption: WEP / Hex, Key: aaaaaaaaaaaaaaaaaaaaaaaaaa (26 a in total)
Note: We have video tutorial, please click column "Video" to watch or contact our customer service to get the video.
What should you pay attention to:
1) From software 2019.09 on, DAS icon will not shown on the desktop, DO NOT ADD this DAS icon by yourself when you use the software. Otherwise it will cause some error even destroy the software by doing this. We will charge fee if software is destroyed by this way.
2) If you need to use DAS to diagnose your car. Just enter Xentry. If your car need to be done by DAS, then software will switch to DAS interface automatically
3) Battery: When you first time to use this SD C4, you need to use the 100% brand new battery on the main unit, not rechargable battery! After done, then no need battery for main unit anymore if you use this software all the time. Because this battery is for update. If you use newer software in the future, then when you first time use the newer software, you need to use new battery for update again.
4) For USA configuration DOIT system after 2014. ALL star C3, C4, SD C4 does not support. For DOIT system after 2014, need to use XENTRY C5 to work.
5) Star software after 2019.09 does not have alone DAS simulaton, you can enter the software from xentry simulation.
1pc x MB SD C4 Multiplexer
1pc x OBDII 16PIN Cable
1pc x 38PIN Cable
1pc x 14PIN Cable
1pc x 8PIN Cable
1pc x Lan Cable
1pc x Hard Disk (2019.09)
MB SD Connect C4 Wire Connection Picture:
MB SD C4 Wireless Connection Picture:
MB SD C4 Hareware version:
SD Connect C4 Languages:
MB SD C4 Scanner PCB Board Display: