This all-system scan tool supports free lifetime use (including the basic diagnostic function of the full system, OBDII full function, and 28+ common maintenance functions) and updates to keep diagnostic software updated and cover more new car models, which will save you a lot of money on updates compared to other devices that require annual payments.
Fits for more GM cars:
· For Chevrolet Tracker/For Suburban/For Tahoe 2023
· For Chevrolet Onix 1.0L(L4F/L4G/LIJ/LIF)/Onix 1.2L(LIF) 2020-2023
· For Cadillac Escalade/Escalade ESV 2021
· For GMC YUKON/YUKON XL 2021
· For Chevrolet Tracker 2020
Live Data Stream
Thinkscan Max2 supports viewing the real-time data flow of various system components to monitor the real-time status and data of the system operation of the vehicle to judge the health status. It displays each data source as a digital or graph and supports up to 4 textual groups to generate graphics data streams simultaneously. It also supports screen recording and screenshot that is convenient for better recording of car failures.
THINKCAR ThinkScan Max 2 has 28 service functions:
It allows you to reset various systems in your vehicle. support more function than other scanners priced similarly
1. Oil Reset ( Supports 53 Brands )
The lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset themileage or driving time to zero after the maintenance, so the maintenance light will go out and the systemwill start a new maintenance cycle.
2. Elec.Throttle Adaption ( Supports 37 Brands )
Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learningvalue of the ECU returns to the initial state.By doing these, the movement of the throttle (or idle motor)can be more accurately controlled, thus adjust the intake volume.
3. SAS - Steering Angle Reset ( Supports 44 Brands )
To reset the steering angle, first find the relative zero point position for the car to drive in straight line.Taking this position as reference, the ECU can calculate the accurate angle for left and right steering.After replacing the steering angle position sensor, replacing steering mechanical parts (such as steeringgearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recoveringcar body, you must reset the steering angle.
4. Battery Matching ( Supports 33 Brands )
This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, inwhich the original low battery fault information will be cleared and battery matching will be done.
5. ABS Bleeding ( Supports 34 Brands )
When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system torestore ABS brake sensitivity. lf the ABS computer,ABS pump, brake master cylinder, brake cylinder, brakeline, or brake fluid is replaced, the ABS bleeding function must be performed to bleed the ABS.
6. Brake Reset ( Supports 41 Brands )
lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to theon-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad.Otherwise, the car alarms.
7. DPF Regeneration ( Supports 39 Brands )
DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuouscombustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reducePM ignition combustion) to stabilize the filter performance.
8 Gear Learning ( Supports 22 Brands )
The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computerto more accurately diagnose engine misfires. lf gear learning is not performed for a car equipped withDelphi engine, the MlL turns on after the engine is started.The diagnostic device detects the DTC P1336'gear not learned'. In this case, you must use the diagnostic device to perform gear learning for the car.After gear learning is successful, the MIL turns off. After the engine ECU, crankshaft position sensor, orcrankshaft flywheel is replaced, or the DTC 'gear not learned" is present, gear learning must be performed.
9. IMMO Service ( Supports 46 Brands )
To prevent the car being used by unauthorized keys, the anti-theft key matching function must beperformed so that the immobilizer control system on the car identifies and authorizes remote control keysto normally use the car. When the ignition switch key, ignition switch, combined instrument panel,ECu,BCM, or remote control battery is replaced, anti-theft key matching must be performed.
10. Injector Coding ( Supports 47 Brands )
Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder soas to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced,injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identifyinjectors to accurately control fuel injection.
11. TPMS Reset ( Supports 39 Brands )
After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting functionmust be performed to reset tire pressure and turn off the tire pressure MIL.Tire pressure resetting mustbe performed after maintenance is performed in the following cases: tire pressure is too low, tire leaks, tirepressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged,andtire is replaced for the car with tire pressure monitoring function.
12. Suspension Matching ( Supports 14 Brands )
This function can adjust the height of the body. When replacing the body height sensor in the airsuspension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration.
13. AFS Reset ( Supports 21 Brands )
This feature is used to initialize the adaptive headlamp system.According to the ambient light intensity, theadaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjustthe headlamp lighting angle while monitoring the vehicle speed and body posture.
14. A/T Learning ( Supports 14 Brands )
This function can complete the gearbox self-learning to improve gear shifting quality. When the gearbox isdisassembled or repaired (after some of the car battery is powered off), it will lead to shift delay or impactproblem. In this case, this function needs to be done so that the gearbox can automatically compensate according to the driving conditions so as to achieve more comfortable and better shift quality.
15. Sunroof Initialization ( Supports 4 Brands )
This function can set the sunroof lock off, closed when it rains,sliding / tilting sunroof memory function,temperature threshold outside the car etc.
16. EGR Adaption ( Supports 10 Brands )
This function is used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced.
17. ODO Reset ( Supports 10 Brands )
a) ODo reset is to copy,write, or rewrite the value of kilometers in the chip of odometer by using a cardiagnostic computer and data cable, so that the odometer shows the actual mileage.
b)Usually when the mileage is not correct due to the damaged vehicle speed sensor or odometer failure, it is necessary to do ODo reset after maintenance.
18. Airbag Reset ( Supports 12 Brands )
This function resets the airbag data to clear the airbag collision fault indicator. When the vehicle collidesand the airbag deploys, the corresponding fault code of the collision data appears, the airbag indicatorlights up, and the fault code cannot be cleared. Since the data inside the airbag computer is disposable,it is required that all new accessories must be replaced, but after performing this function, the data of theairbag computer can be recovered and the fault code can be cleared, the airbag light will go out, and theairbag computer can continue to use.
19. Transport Mode ( Supports 13 Brands )
ln order to reduce power consumption, the following functions may be disabled,including limiting thevehicle speed, not waking up the door opening network, and disabling the remote control key, etc. At thistime, the transport mode needs to be deactivated to restore the vehicle to normal.
20. A/F Reset ( Supports 5 Brands )
This function is applied to set or learn Air/Fuel ratio parameters.
21. Stop/Start Reset ( Supports 5 Brands )
This function is used to open or close the automatic start-stop function via setting the hidden function inECU(provided that the vehicle has a hidden function and supported by hardware).
22. NOx Sensor Reset ( Supports 12 Brands )
NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. lf theNOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalyticconverter learned value stored in the engine ECu.
23. AdBlue Reset (Diesel Engine Exhaust Gas Filter - Supports 8 Brands)
After the diesel exhaust treatment fluid (car urea) is replaced or flled up, urea reset operation is required.
24. Seat Calibration ( Supports 26 Brands )
This function is applied to match the seats with memory function that are replaced and repaired.
25. Coolant Bleeding ( Supports 5 Brands )
Use this function to activate the electronic water pump before venting the cooling system.
26. Tyre Reset ( Support 13 Brands )
This function is used to set the size parameters of the modified or replaced tire.
27. Windows Calibration ( Supports 24 Brands )
This feature is designed to perform door window matching to recover ECU initial memory, and recover theautomatic ascending and descending function of power window.
28 Language Change ( Supports 22 Brands )
This function is used to change the system language of the vehicle central control panel.
Share & Print the Diagnosis Report
You can scan by QR code to get the report and share the report or choose to share it directly.
It supports online feedback and WiFi connection is required. After clicking "Feedback", upload the file and fill in the detailed description of the problems encountered in the diagnosis process, and enter the email address to submit feedback. Those can help our engineers to solve your problem as soon as possible.
A file of diagnostic data that is automatically saved each time a vehicle diagnostic is performed can be viewed in the History.
Other Functions:
AUTOVIN SCAN:
click "diagnose" and "autosearch" after connecting to the vehicle. Then the thinktool mini automotive diagnosti tool will begin to scan the VIN automatically.
One-Key Wifi Update:
no need to update on computer. Just click update after connecting wifi, then all softwares will start to update. (you will enjoy lifetime update through one-key wifi update, which is rare in diagnostic market as other diagnostic tools only offer one year free update.)
One-Key Screenshot:
use the feature to capture and save the diagnostic process for you rather than take pictures by telephone.
One-Key Screen Recorder:
you will hardly find this feature on other scanners. This is one of the biggest advantage of thinktool Mini, which will be a big surprise to those who like recording video of the whole diagnostic process. With this feature, you don't need to hand up a telphone during the diagnosis.
Coverage 93+ Vehicle Brand
Compatible with 95% of all car models from the US, Europe, and Asia.
America: for Chrysler, for Ford, for GM, for Dodge, for Jeep, for Buick, for Lincoln, for Cadillac, etc.
Europe: for AstonMartin, for Benz, for Sprinter, for BMW, for Ferrari, for Fiat, for LandRover, for Maserati, for Opel, for Peugeot, for Porsche, for Lancia, for LT3, for Maybach, for Mini, for Seat, for Skoda, for Vauxhall, for Volkswagen CV, for Renault, for Saab, for Smart, for Volvo, for Volkswagen, for Abarth, for Alfa,for Audi, for Bentley, for Bugatti, for Citroen, for Dacia, for Jaguar, for Lambor Ghini, etc.
Asia: for Acura, for Daewoo, for Daihatsu, for Honda, for Hyundai,for Infiniti,for Isuzu, for Kia,for Lexus, for Maruti Suzuki, for Mazda, for Mitsubishi, for Nissan, for SsangYong, for Subaru, for Suzuki, for Toyota, for GTR, for Scion, etc.
Two Ways to Connect with car :
wireless diagnosis VS wire diagnosis
wireless diagnosis: thinktool + wireless connector
diagnostic distance: 5-10 m
wire diagnosis: scanner+ diagnostic cable
diagnostic distance: 1m
Many traditional diagnostic scan tools are equipped with diagnostic cables and you have to connect the car scanner with the OBDII port via cable during the diagnosis, which limits the diagnostic distance within 1m. While thinktool offers wireless connector, making it convenient and efficient during the work. The diagnostic distance can be 5-10 m.
Just need 3-step quick registration
Step 1 : Choose Time Zone
Step 2 : Agree the agreement term
Step 3 : New Registration , Create APP Account
How to find the password when Register scanner?
there has the password letter in the package , pls find it in the package directly.
Specification for Thinkcar MAX 2:
THINKTOOL Host Computer
• Screen Size:5.99”
• Operation System: Android
• Battery Capacity:3150mAh/3.7V
• Capacity:32GB
• Resolution:720*1440 Pixel
• Working Voltage:5V
• Working Current:≤2.5A
• Dimension:120.5*65*29mm
• Working Temperature: -10℃ to 50℃ (14℉ to 122 ℉)
• Storage Temperature: -20℃ to 60℃ (-4℉ to 140 ℉)
THINKTOOL VCI
• Working Voltage:12V
• Working Current:≤60mA
• Working Temperature: -10℃ to 50℃ (14℉ to 122 ℉)
• Storage Temperature: -20℃ to 60℃ (-4℉ to 140 ℉)
Packing List
1x THINKTOOL Host Computer
1xTHINKTOOL VCI
1x Charging Cable
1x Charging Plug Adapter
3x Convertible Plugs
1x Manual
1x Carry Bag