XPROG-M V6.12 ECU Programmer With USB Dongle, No need activation.
with new authorization: AUTH-0028-1 Renesas V850 Authorized and AUTH-0028-2 Renesas SuperH Authorized 2017/10/9.
Xprog V5.84 adds new authorizations: AUTH-0028-1 Renesas V850 Authorized and AUTH-0028-2 Renesas SuperH Authorized 2017/10/9
BMW EWS-4.3 & 4.4 IC Adaptor (No Need Bonding Wire) for X-PROG /AK90/R270/R280 PLUS Programmer, Reading & writing data dump from EWS Immobilize, Can work with “ X-PRO, AK90 and R270 “ programmer, Without soldering any wires, just on board.
ATMEGA64 Repair Chip Update any version XPROG-M to latest V5.55
1.Most stable software so far now.
2. Engineers were always othered by the software problem of other version before, now you can take it easy. We have tested different versions from V5.0 to V5.55, all version works greatly.
V5.5.5 XPROG-M ECU Programmer, the only tool for decryption BMW CAS4, with Hard disk. Software is preinstalled, you can directly use when you receive the package.
XPROG-M V5.5.5 X-PROG M BOX V5.55 ECU Programmer
1. It is the newest version of XPROG-M ECU Programmer.
2. It is the only tool can decryption BMW CAS4.
3. The package comes with T420 laptop, Hard disk and USB Dongle.
4. Software is pre-installed, you can use directly when you receive the package.
ATMEGA64 Repair Chip help you update your XPROG-M from V5.0/V5.3/V5.45 to V5.48, no dongle needed, full authorization support, including CAS4! Any hardware XPROG-M Programmer all can use it.
XPROG M ATMEGA64 Repair Chip help you update your XPROG-M from V5.0 or V5.3 to V5.45, no dongle needed, support more MCU and Authorization.
Xprog-M V5.3 USB Dongle is for Xprog-M V5.3. If your xprogm dongle is lost, you can buy this one.
X-PROG Box ECU Programmer XPROG-M V5.74 with USB Dongle Adds new authorization: AUTH-0025 Authorized 11/4/2014,No operation system limitation, software can be installed on both Windows XP and Windows 7.
XPROG-M V5.55 XPROG M Programmer with USB Dongle,the only version XPROG-M can decypte new version BMW CAS4.Add new authorization: AUTH-0025 Authorized 11/4/2014
XPROG-M V5.60 XPROG M Programmer with USB Dongle,without operation system limitation, software can be installed on Windows XP, windows 7.This is the only version for XPROG-M that can decypte new version BMW CAS4.New authorization was added: AUTH-0025 Authorized 11/4/2014
The XPROG-box project is a continuation of the project XPROG and now supports more than 450 units (serial EEPROM's, Microcontrollers (MCU), Electronics Control Units (ECU), DashBoards, Immobilizers, Calculators and others).
The XPROG-box project is a continuation of the project XPROG and now supports more than 450 units (serial EEPROM's, Microcontrollers (MCU), Electronics Control Units (ECU) and others).
Xprog-m box software version 5.51 , only can use our software-CD, otherwise the hardware will be damaged without any warranty, cannot be repaired if you use other version software(lower or higher) or try to update the software or hardware.
Clip for Xprog V5.60 /V5.74/5.84 XPROG-Box, UPA ECU Programmer reading 8pin chip without removing.
Also this clip adapter can work with UPA USB Programmer.