Launch X431 GIII X-PROG 3 V10.05 Immobilizer & Key Programmer
Launch X431 G3 Highlights:
1. All-in-One Key Programmer. Integrates Multiple Function Models
2. Reads & Writes Most Engine/ Gearbox ECUs Without Disassembling the Shell
3. Supports VW/ AUDI MQB Platform Engine ECU Replacement or Cloning (Read engine ECU data directly from the key).
4. Works with Reprogramming Device to Backup/ Restore Programming Data (For Bosch/Siemens engine ECU).
5. Compatible with Multiple X-431 Series Diagnostic Tablet (X-431 V, X-431 V+, X431 Pro5, X431 ProS, X431 Pro3s+, X-431 PAD V, X-431 PAD VII, X-DIAG Pro3 etc)
6. Enables Reading/ Writing EEPROM, On-Board MCU, and BMW CAS4+/ FEM Chips, Mercedes-Benz Infrared Keys, Generating Special Keys, Reading BMW Engine ISN Code.
7. You can buy MCU3 Adapter to do Benz All Keys Lost and ECU TCU Reading.
Check Latest X-PROG3/GIII Car List
New Software Update V10.07 (Nov, 30th, 2021):
Added the Flash & Eeprom data decryption function for one gearbox VL381 of VW series immobilizer independent software/car model diagnostic software.
Added the MCU reading/writing function for one RENESAS MCU of BCM2 (D70F3381). Optimized the clone function for the VL381 gearbox.
Optimized the ECU reading/writing function for the Simos8.6 engine.
Optimized the clone function for the VL381 gearbox.
Fixed Bugs
V10.06 Update
1) Added the Siemens engine clone and Flash&Eeprom data decryption functions for the immobilizer independent software/car model diagnostic software of SIMOS8.5 and SIMOS8.6 VW series.
2) Added the EEPROM data reading (after unpacking) function for the fourth-generation comfort computer of immobilizer independent software/VW model diagnostic software.
3)Added the ECU read/write function for the SIMOS SDI6, SIMOS SDI7, and SIMOS SDI8 Siemens engines.
4)Added ECU reading and writing functions for 5 models of Transmission including MPS6_GEN3, BMWDKG, DKG_G2, DQ200G2 and MPS6 series.
V10.05 Update
Added ECU reading and writing functions for 10 models of Siemens Engine including MSD80, MSD81, MSD85, MSD87, MSV90, SIM271DE, SIM271KE, SIMOS8.4, SIMOS8.5 and SIMOS8.6;
Added ECU reading and writing functions for 5 models of Transmission including 9G_Tronic, DQ380, AL551, AL450 and 8HPXX.
X431 X-PROG 3 Functions
1. Read BMW engine ISN code.
2. Read/write BMW CAS4+ and FEM chips.
3. Read/write Audi fifth-generation steering column chips
4. Read/write EEPROM.
5. Read/write MCU.
6. VW Fourth-generation Dump Mode All Keys Lost.
7. Read engine in BENCH mode.
8. Read gearbox data.
More features are constantly updated
XPROG3 Advantages (Cloning function only available with PAD V/PAD VII/Pro5/Turbo/ Throttle etc)
1. Supports VW/AUDI MQB platform engine ECU replacement or cloning (Read engine ECU data directly from the key).
2. Supports VW/AUDI MQB platform gearbox ECU replacement or cloning.
3. Supports ECU replacement for the fifth-generation of Audi (0AW/0B5) gearbox.
4. Supports reading, writing & cloning the ECU for the fourth-generation of VW UDS engine.
5. Supports BMW E chassis 8HP gearbox ECU reprogramming to empty.
6. Works with reprogramming device to backup/restore programming data (For Bosch/Siemens engine ECU).
Compatible With Multiple X-431 Series Diagnostic Tablet:
X431-Throttle, X431-Throttle III, X431-Torque, X431-Torque III, X431-Turbo, X431-PAD II AE
X431 Pros, X-431 PRO GT, X-431 PRO V4.0, X-431 PRO 3 V4.0, X-431 PRO 5, X-431 PAD III V2.0, X-431 PAD V, X-431 PAD VII
Supported Brands
VW, Audi, Skoda, SEAT, BMW, Mercedes-Benz, Toyota… (updates to be continue)
X-PROG3 Features:
1. Compatible with X-431 series diagnostic scanners, X-PROG 3 enables reading/writing EEPROM, on-board MCU and BMW CAS4+/FEM chips, Mercedes-Benz infrared keys, generating special keys, reading BMW engine INS code.
2. Supported brands: VW, AUDI, SKODA, SEAT, BMW, MERCEDES-BENZ, TOYOTA, etc. More models continue to be updated.
3. Supported systems: Automatic Transmission, Instrument System, CAS, Body System, Lock System, etc.
4. Compatible with: X-431 PRO GT, X-431 PRO V4.0, X-431 PRO 3 V4.0, X-431 PRO 5, X-431 PAD III V2.0, X-431 PAD V, X-431 PAD VII
5. Reads & writes most Engine/Gearbox ECUs without disassembling the shell
Launch X431 G-3 Core Functions
1. Integrated the functions of key matching/copy, anti-theft IC reading & writing, and ECU reading & writing, etc.
2. Supports common ECU/MCU/EEPROM major manufacturers, with over 1200 product models, and constantly updating.
3. Supports ECU replacement for all lost without disassembly for VW/AUDI non-35XX instrument (it can be read directly through independent harness without removing the IC).
4. Supports ECU replacement for the fourth-generation of VW/AUDI engine;
5. Supports ECU replacement for the fifth-generation of VW/AUDI Bosch and Siemens engines.
6. Supports the all lost and replacement for the fourth generation of AUDI EZS, comfortable ECU, and KESSY IC.
7. Supports the BMW F and G chassis 8HP gearbox ECU reprogramming to empty.
8. Supports the BMW CAS4/CAS4+ module replacement.
9. Supports the ECU cloning and replacement for BMW Siemens engines.
10. Erase the password for Mercedes-Benz engine and gearbox within 3S.
11. Add the function of calculating the password for the Mercedes-Benz key within 1 minute.
Supported Chip Brands:
It supports common mainstream ECU MCU manufacturers, with more than 1,000 product models, and they are continuously being updated.
Supported EEPROM Brands:
It supports common mainstream EEPROM manufacturers, with nearly 1,000 product models, and they are continuously being updated.
X-prog3 ECU TCU Clone Function Only with high-end tablets (PAD5, PAD 7, PRO5, IMMO PLUS etc)
XPROG3 Operation Connection:
Connection method 1: Directly connect to OBD16 for key matching, data reading and writing, etc
Connection method 2: Place the anti-theft EEPROM or MCU chip in the chip burning socket, and then insert the chip burning socket into the slot of the immobilizer programmer locker and lock it to realize the data interaction between the IC anti-theft chip and the diagnostic host
Connection method 3: After removing the ECU from the car, connect the anti-theft ECU pin to the DIY slot of the immobilizer programmer through the cable to realize the data interaction between the anti-theft ECU and the diagnostic host.
How to Update Launch X-PROG3 Software?
1.On the main diagnostic screen, tap Software Update to enter the update center. Check the software you want to upgrade, and then tap Update.
2.Once downloading completes, the software packages will be installed automatically.
Launch X-Prog vs X-Prog 3
Item Name | X-prog | X-Prog 3 |
EEPROM Read and Write | × | √ |
MCU Read and Write | × | √ |
Mercedes Benz Key | × | √ |
Key Simulator | × | √ |
VW 4th instrument disassembly/reading/all lost | × | √ |
Read Engine via Bench Mode | × | √ |
Read Engine via Boot Mode | × | √ |
VW 4th All Key Lost without Account | × | √ |
Read Gearbox | × | √ |
Read and Write Key | √ | √ |
Read BMW ISN | × | √ |
Read CAS4+/FEM Chip | × | √ |
Audi 5th generation steering column chip reading and writing | × | √ |
Replace OBD Reading Component | √ | √ |
Interface | DB26, DB15 |
Input Power | DC12V |
Working CurrentMax | 500mA |
Power Consumption | 5W |
Storage Temperature | -20℃~70℃ |
Working Temperature | 0℃~50℃ |
Package List:
1set x Launch X-PROG 3
Launch X431 X-PROG vs. X-PROG3
Item | Launch X431 X-PROG
|
Launch X431 X-PROG3
|
Read/Write EEPROM | No | Yes |
Read/Write MCU | No | Yes |
Mercedes Benz Keys | No | Yes |
Key simulator | No | Yes |
VW 4th IMMO Dump Mode All Keys Lost | No | Yes |
Read engine in Bench mode | No | Yes |
VW 4th IMMO enumeration all keys lost | No | Yes |
Read gearbox data | No | Yes |
Read and write keys | Yes | Yes |
Read BMW engine ISN code | No | Yes |
Replace OBD reading component | Yes | Yes |
Read & Write BMW CAS4+ and FEM chips | No | Yes |
Read engine in Boot mode | No | Yes |
Read & Write Audi 5th generation steering column chips | No | Yes |
Specification | ||
Interface | DB15 | DB15,DB26 |
Input Power | DC12V | DC12V |
Working current Max | 200mA | 500mA |
Power consumption | 2W | 5W |
Storage Temperature | -20℃-70℃ | -20℃-70℃ |
Working Temperature | -10-50 0℃ | 0-50℃ |
Size | 142 x72 (mm) | 228 x120 (mm) |