Compatible with OBDSTAR X300 DP Plus/X300 Pro4/ Odomaster/ P50.
OBDSTAR CANFD Adapter is used for diagnosing ECU systems of cars with CAN FD protocols and reset Hyundai/Kia airbag.
Required to access 80 % of Chrysler / Fiat 2018 vehicles
Required to access 100 % of Chrysler / Fiat 2019 vehicles
Access Chrysler / Fiat vehicles using Secure Gateway module, Allow to read and delete codes, Perform active tests
Autel’s CAN FD Adapter enables diagnostics of vehicles using the CAN FD (CAN Flexible Data-Rate) protocol used on newer GM and Ford vehicles.
The Chrysler 12+8 Adapter is Autel's bypass for Chrysler's Security Gateway Module (SGM) which limits an aftermarket scan tool to only reading DTCs and viewing data.
Used with AUTEL IM608 IM508 IM600 IM100.
for Nissan Sylphy Sentra (Models with B18 Chassis) Key Adding without Password.
Exclusive release of TOYOTA 30PIN connector (no need to pierce the harness), supports 4A and 8A-BA types.
Used with LONSDOR K518ISE and K518S.
Supports HPLA JPLA K8D2 Version All Keys Lost with active alarm via OBD.
Used with X300 DP, X300 DP Plus, and Pro4.
Supports All Keys Lost for Toyota 8A & Ford 2017- Proximity
With P002 Adapter, TOYOTA 8A Cable, Ford All Key Lost Cable.
XTOOL 8+12 Cable Adapter for Chrysler vehicles 2018 and later
Not Universal. Only work with XTOOL tablets X100PAD, X100PAD2, X100PAD3, EZ400PRO, A80PRO , A80PRO MASTER, D7, D8, D9, D9PRO and so on.
Used with VVDI KEY TOOL PLUS.
Supports all keys lost programming while alarm on.
No need to power off over and over again
Used with OBDII tools from AUTEL, LAUNCH X431,XHORSE, OBDSTAR, ect.
Adds Toyota Corolla Cross (2022-), Frontlander (2022-) 4A-BA Proximity (board number 1320 2561) add key and all keys lost
Adds 2022- BZ4X, Granvia, Harrier, Venza, Sienna, Wildlander, Sequoia, Tundra, Land Cruiser 8A-BA type add key and all keys lost without pin code
The converter can be used with X300 DP/ X300 DP Plus/ X300 PRO4/ Odo Master/ X200 PRO2 and other programmers (Autel, Launch X431 etc) to program keys, correct mileage or oil reset via OBD II for 2018 and up FIAT/ CHRYSLER/ ALFA ROMEO vehicles.
The CAN-FD adapter supports 2020 and newer model year vehicles using the Controller Area Network Flexible Data-Rate protocol, and is an extension to the original CAN bus protocol that was specified in ISO 11898-1.
All 2018 Fiat,Chrysler, Alfa vehicles are equipped with SGW security gateway modules to prevent access to the vehicle from the OBD2 port via a non-original diagnostic scanner. The purpose of this module is to prevent attacks on the vehicle network via the CAN BUS.
Compatible with X300 DP/ X300 DP Plus/ X300 PRO4/ Odo Master/ X200 PRO2 and other programmers (Autel, Launch X431 etc)
The Lonsdor L-JCD Chrysler 2018+ cable can be connected to the vehicle throw Chrysler star connector, Chrysler instrument cluster plug & Chrysler RFHUB computer connector.
NISSAN-40 BCM CABLE is mainly used for proximity key adding and all key lost (no need pincode) for Nissan Hennessy/Kiwi T33/Pathfinder, Mitsubishi Outlander etc.
Work Together with Xhorse Key Tool Plus Pad
Used in Key Programming and Cluster Calibration via OBD2
The Nissan 40 pin BCM cable can be used to replace 16+32 gateway adapter if using Lonsdor k518 series devices.
Launch X431 CAN FD Adapter, used together with X431 V+, X431 Throttle, X431 PAD V/II.
It is mainly for the detection of license plates of CAN FD communication protocols such as GM, Jaguar, and Land Rover (reading fault codes, data streams and other special functions).